Kenner Welding Online Only Auction
Bidding opens August 8th at 12:00pm CT
Bidding begins to close on August 13th at 6:00pm CT
301 Sunny Hills Road - Devils Lake, ND 58301
Gerald had a prominent welding career over 20 years but due to health restrictions not allowing him to pick up the leads anymore he is liquidating his welding equipment. Check out the well taken care of tools and tractor too.
Local Pickup Only
Bidding Notice: This is an internet-only auction. All bidding will take place online.
Lot 1 | Oliver 1600 with Buhler allied loader
Gas Oliver 1600 shows 4531 hours. Three point, PTO. loader ran off of PTO pump and auxiliary hydraulic tank. Very good shape straight tin, good paint, runs and drives great. 7’ bucket straight
Lot 2 | Shop built heavy duty press two jacks
One 30ton one 10 ton jack, roughly 80 inches wide by 34 inches stands at 90 inches tall
Lot 3 | 10‘ x 16‘ metal rack with metal contents
includes all metal scraps and pieces in photos.
Lot 4 | Scaffolding set
scaffolding set, very straight, good condition
Lot 5 | Torch cart
Oxy-acetylene torch on big wheel cart set up for propane at the moment torch works either way tanks are owned heating and welding tip
Lot 6 | Hobart handler 140 wire feed welder
Hobart handler 140 wire feed with cart less tank 110 plug-in, very little use on this unit, great working welder. Tank Not Included
Lot 7 | Miller Matic 200 Wire feed welder
Miller MillerMatic 200 amp wire welder very good condition single phase
Lot 8 | Miller XMT304 inverter wire or arc welder
miller 300 amp inverter welder on cart, very good working order. Single phase
Lot 9 | 22 inch 5 hp chopsaw
Industries is 22 inch chopsaw single phase. 19 brand new cutting wheels. Good working order.
Lot 10 | Thermal dynamics cut master 58 plasma cutter
Thermal dynamics cut master 58 plasma cutter on rolling cart little use great shape. Single phase
Lot 11 | Miller Dialarc HF TIG welder
Arc and tig welder 25 foot Tig lead
Lot 12 | 3 hp pedestal grinder
2x12 grinding stones, one new stone single phase
Lot 13 | Clausing heavy duty drill press
Converted to single phase good working heavy duty drill press
Lot 14 | Drill bit set 5/8- 1 1/2"
Good heavy bit set
Lot 15 | Shop built welding rod storage cabinet on stand
Lot 16 | Craftsman 10" table saw, on wheels
Lot 17 | Black and decker heavy duty reciprocating saw
Corded, good working order
Lot 18 | Two 2-ton beam clamps
2-15/16"-8-5/8” or 75-220mm Very good shape
Lot 19 | 25’ welder extension cord
Lot 20 | 2) Armstrong no. 412 clamps
12" grip
Lot 21 | 2) Jorgensen 10" c-clamps
Lot 22 | Dewalt D28493 7"/9” angle grinder
5000rpm very good condition
Lot 23 | Milwaukee hole hawg
High rpm 1200, low rpm 300. Sn 413-412135
Lot 24 | Milwaukee 8 1/4" circular saw
Very good condition
Lot 25 | Milwaukee 2" die grinder
14,500 rpm good working order
Lot 26 | Sheet gripper
1/16- 4" grip, 1 ton capacity. Good teeth
Lot 27 | Assorted copper clad electrodes
Boxes are all open and partially full, still lots of electrodes
Lot 28 | Sealed 1/8 e6010 electrodes
Sealed can 50lb
Lot 29 | Sealed can 5/32 e7018
Sealed 50lb can
Lot 30 | New 5lb of 3/32" 7018 electrodes
7018 low hydrogen electrodes
Lot 31 | New 5lb 3/32 7018 electrodes
Low hydrogen premium electrodes
Lot 32 | Sealed Lincoln 5lb 3/32"x12” 6011
Fleetwood 180-RSP 3/32 e6011 electrodes
Lot 33 | Two containers 5/32 7018 electrodes
Good dry kept
Lot 34 | Container of 3/16 7018
Kept dry
Lot 35 | Air arc gouging tool
good working order.
Lot 36 | Linde Tig rig
Lot 37 | Victor journeyman torch set
Cutting and heating tips and new cutting tip both cutting tips are for propane
Lot 38 | Miller spoolmatic 1
Spooltool with extra tips
Lot 39 | Thermal dynamics tips for plasma cutter
Lot 40 | New weldmark flowmeter
Lot 41 | Leather padded welding knee pads
Lot 42 | Soft leather welding hood
Good for tight welding spots
Lot 43 | 36" aluminum pipe wrench
Good teeth
Lot 44 | Ridgid 1/8"-2” pipe vice
Not been used
Lot 45 | 33lb spool .035 wire
Lot 46 | New 2 5/16 hitch replacement
Lot 47 | 28 ft no. 10 camper cord
Lot 48 | 4) heavy built jackstands
18-31" tall
Lot 49 | Two screw adjust jackstands
29-48"
Lot 50 | Adjustable metal roller stand
29.5"-46” high
Lot 51 | Adjusting rolling V-stand
28"-41” adjustment
Lot 52 | Miller mig tool 15’ new liner
Lot 53 | 2 welding hoods
Lot 54 | Gooseneck hitch
Lot 55 | 28"x29” rolling metal cart 5” casters
